Hp 250 Hi-performance Adhesive Hardener Hp250 Hi-performance

Preparing to load PDF file. please wait...

0 of 0
100%
Hp 250 Hi-performance Adhesive Hardener Hp250 Hi-performance

Transcript Of Hp 250 Hi-performance Adhesive Hardener Hp250 Hi-performance

MSDS Name
Manufacturer Name Stock No.: Kit MSDS Revision Date
Components :

DEVCON® HP250 (2:1 ratio) straw - use DA091 2:1 plunger ITW Devcon 14315 12/15/2009
HP 250 HI-PERFORMANCE ADHESIVE HARDENER HP250 HI-PERFORMANCE ADHESIVE RESIN
ITW Devcon Product Code : 14315

Save page as PDF

View MSDS : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION

Product Name: Manufacturer Name: Address:
General Phone Number: Emergency Phone Number: CHEMTREC: Canutec: MSDS Revision Date:

HP 250 HI-PERFORMANCE ADHESIVE HARDENER ITW Devcon 30 Endicott Street Danvers, MA 01923 (978) 777-1100 (800) 424-9300 For emergencies in the US, call CHEMTREC: 800-424-9300 In Canada, call CANUTEC: (613) 996-6666 (call collect) 12/15/2009

HMIS Health Hazard 3*
Fire Hazard 1
REACTIVITY 0 Personal x Prote ction
* Chronic Health
Effe cts :

SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Name

CAS#

Ingredient Percent

Inert material Nonylphenol Non-hazardous ingredients. 4, 4'-Methylenebiscyclohexanamine Triethylene glycol diamine Aminoethylpiperazine PACM Oligomers

N/A 25154-52-3 N/A 1761-71-3 929-59-9 140-31-8 135108-88-2

5 - 10 by weight 10 - 30 by weight 30 - 60 by weight 10 - 30 by weight 10 - 30 by weight 1 - 5 by weight 1 - 5 by weight

SECTION 3 - HAZARDS IDENTIFICATION

Emergency Overview: Route of Exposure:

DANGER! Corrosive. Potential Sensitizer. Irritant. Eyes. Skin. Inhalation. Ingestion.

SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION

Product Name: Manufacturer Name: Address:
General Phone Number: Emergency Phone Number: CHEMTREC: Canutec: MSDS Revision Date:

HP250 HI-PERFORMANCE ADHESIVE RESIN ITW Devcon 30 Endicott Street Danvers, MA 01923 (978) 777-1100 (800) 424-9300 For emergencies in the US, call CHEMTREC: 800-424-9300 In Canada, call CANUTEC: (613) 996-6666 (call collect) 12/15/2009

HMIS Health Hazard 2*
Fire Hazard 1
REACTIVITY 1 Personal x Prote ction
* Chronic Health
Effe cts :

SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Name

CAS#

Ingredient Percent

Modified Bisphenol F Epoxy Resin Elastomer Modified Diglycidyl Ether Bisphenol A diglycidyl ether resin Neopentyl glycol diglycidyl ether Inert material Phenol, polymer with formaldehyde, glycidyl ether

71617-64-6 68909-14-8 25068-38-6 17557-23-2 N/A 28064-14-4

10 - 30 by weight 10 - 30 by weight 30 - 60 by weight 1 - 5 by weight 1 - 5 by weight 10 - 30 by weight

SECTION 3 - HAZARDS IDENTIFICATION

Emergency Overview: Route of Exposure: Potential Health Effects:
Eye:
Skin:
Inhalation:
Ingestion: Chronic Health Effects: Signs/Symptoms: Target Organs: Aggravation of Pre-Existing Conditions:

WARNING! Potential Sensitizer. Irritant. Eyes. Skin. Inhalation. Ingestion.
Can cause moderate irritation, burning sensation, tearing, redness, and swelling. Overexposure may cause lacrimation, conjunctivitis, corneal damage and permanent injury.. Can cause skin irritation; itching, redness, rashes, hives, burning, and swelling. Allergic reactions are possible. May cause skin sensitization, an allergic reaction, which becomes evident on reexposure to this material. Respiratory tract irritant. High concentration may cause dizziness, headache, and anesthetic effects. May cause respiratory sensitization with asthma-like symptoms in susceptible individuals.
Causes irritation, a burning sensation of the mouth, throat and gastrointestinal tract and abdominal pain.
Prolonged skin contact may lead to burning associated with severe reddening, swelling, and possible tissue destruction. Overexposure can cause headaches, dizziness, nausea, and vomiting.
Eyes. Skin. Respiratory system. Digestive system. Individuals with pre-existing skin disorders, asthma, allergies or known sensitization may be more susceptible to the effects of this product.

SECTION 4 - FIRST AID MEASURES

Eye Contact:

Immediately flush eyes with plenty of water for at least 15 to 20 minutes. Ensure adequate flushing of the eyes by separating the eyelids with fingers. Get immediate medical attention.

Skin Contact: Inhalation: Ingestion:

Immediately wash skin with plenty of soap and water for 15 to 20 minutes, while removing contaminated clothing and shoes. Get medical attention if irritation develops or persists.
If inhaled, remove to fresh air. If not breathing, give artificial respiration or give oxygen by trained personnel. Seek immediate medical attention.
If swallowed, do NOT induce vomiting. Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person.

SECTION 5 - FIRE FIGHTING MEASURES

Flash Point: Flash Point Method: Auto Ignition Temperature: Lower Flammable/Explosive Limit: Upper Flammable/Explosive Limit: Fire Fighting Instructions:
Extinguishing Media:
Unsuitable Media: Protective Equipment:
Unusual Fire Hazards:

>200°F (93.3°C)
Estimated.
Not determined.
Not determined.
Not determined.
Evacuate area of unprotected personnel. Use cold water spray to cool fire exposed containers to minimize risk of rupture. Do not enter confined fire space without full protective gear. If possible, contain fire run-off water.
Use carbon dioxide (CO2) or dry chemical when fighting fires involving this material.
Water or foam may cause frothing.
As in any fire, wear Self-Contained Breathing Apparatus (SCBA), MSHA/NIOSH (approved or equivalent) and full protective gear.
Sealed containers at elevated temperatures may rupture explosively and spread fire due to polymerization.. Heating above 300 deg F in the presence of air may cause slow oxidative decomposition and above 500 deg F may cause po lymeriz atio n.

SECTION 6 - ACCIDENTAL RELEASE MEASURES

Spill Cleanup Measures:
Personnel Precautions: Environmental Precautions: Other Precautions:

Absorb spill with inert material (e,g., dry sand or earth), then place in a chemical waste container. Provide ventilation. Clean up spills immediately observing precautions in the protective equipment section. After removal, flush spill area with soap and water to remove trace residue. Avoid personal contact and breathing vapors or mists. Ventilate area. Use proper personal protective equipment as listed in section 8.
Evacuate area and keep unnecessary and unprotected personnel from entering the spill area.
Avoid runoff into storm sewers, ditches, and waterways.
Pump or shovel to storage/salvage vessels.

SECTION 7 - HANDLING and STORAGE

Handling: Storage: Special Handling Procedures:
Hygiene Practices:

Use with adequate ventilation. Avoid breathing vapor, aerosol or mist.
Store in a cool, dry, well ventilated area away from sources of heat and incompatible materials. Keep container tightly closed when not in use.
Provide appropriate ventilation/respiratory protection against decomposition products (see Section 10) during welding/flame cutting operations and to protect against dust during sanding/grinding of cured product.
Wash thoroughly after handling.

SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION - EXPOSURE GUIDELINES

Engineering Controls:

Use appropriate engineering control such as process enclosures, local exhaust ventilation, or other engineering controls to control airborne levels below recommended exposure limits. Good general ventilation should be sufficient to control airborne levels. Where such systems are not effective wear suitable personal protective equipment, which performs satisfactorily and meets OSHA or other recognized standards. Consult with local procedures for selection, training, inspection and maintenance of the personal protective equipment.

Eye/Face Protection: Skin Protection Description: Respiratory Protection:
Other Protective:
EXPOSURE GUIDELINES Notes :

Wear appropriate protective glasses or splash goggles as described by 29 CFR 1910.133, OSHA eye and face protection regulation, or the European standard EN 166. Wear appropriate protective gloves and other protective apparel to prevent skin contact. Consult manufacturer's data for permeability data. A NIOSH approved air-purifying respirator with an organic vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed exposure limits. Protection provided by air purifying respirators is limited. Use a positive pressure air supplied respirator if there is any potential for an uncontrolled release, exposure levels are not known, or any other circumstances where air purifying respirators may not provide adequate protection. Facilities storing or utilizing this material should be equipped with an eyewash and a deluge shower safety station.
Only established PEL and TLV values for the ingredients are listed.

SECTION 9 - PHYSICAL and CHEMICAL PROPERTIES

Physical State Appearance: Odor: Boiling Point: Melting Point: Specific Gravity: Solubility: Vapor Density: Vapor Pressure: Percent Volatile: Evaporation Rate: pH: Molecular Formula: Molecular Weight: Flash Point: Flash Point Method: Auto Ignition Temperature: VOC Content: Percent Solids by Weight

Viscous. Liquid.. mild. Not determined. Not determined. > 1 Not determined. >1 (air = 1) Not determined. 0 Not determined. Neutral. Mixture Mixture >200°F (93.3°C) Estimated. Not determined. 0 g/L 100

SECTION 10 - STABILITY and REACTIVITY

Chemical Stability: Hazardous Polymerization: Conditions to Avoid:
Incompatible Materials:

Stable under normal temperatures and pressures.
Not reported.
Extreme heat, sparks, and open flame. Incompatible materials, oxidizers and oxidizing conditions. Heating resin above 300 F in the presence of air may cause slow oxidative decomposition.
Strong Lewis or mineral acids, strong oxidizing agents, strong mineral and organic bases (especially primary and secondary aliphatic amines).

SECTION 11 - TOXICOLOGICAL INFORMATION

RTECS Number:

SL6480000

Neopentyl glycol diglycidyl ether :

RTECS Number:

TX3760000

Skin:

Oral - Rat LD50 : 4500 mg/kg [Details of toxic effects not reported other than lethal dose value.]

Ingestion:

Oral - Rat LD50 : 4500 mg/kg [Details of toxic effects not reported other than lethal dose value.]

SECTION 12 - ECOLOGICAL INFORMATION

Ecotoxicity: Environmental Fate:

No ecotoxicity data was found for the product. No environmental information found for this product.

SECTION 13 - DISPOSAL CONSIDERATIONS

Waste Disposal: RCRA Number:

Consult with the US EPA Guidelines listed in 40 CFR Part 261.3 for the classifications of hazardous waste prior to disposal. Furthermore, consult with your state and local waste requirements or guidelines, if applicable, to ensure compliance. Arrange disposal in accordance to the EPA and/or state and local guidelines.
None.

SECTION 14 - TRANSPORT INFORMATION

DOT Shipping Name: DOT UN Number: DOT Hazard Class: DOT Packing Group:

Non regulated. N/A Not applicable. Not applicable.

SECTION 15 - REGULATORY INFORMATION

Modified Bisphenol F Epoxy Resin :

Canada NDSL:

Listed

Elastomer Modified Diglycidyl Ether :

TSCA Inventory Status:

Listed

Canada DSL:

Listed

Bisphenol A diglycidyl ether resin :

TSCA Inventory Status:

Listed

Canada DSL:

Listed

Neopentyl glycol diglycidyl ether :

TSCA Inventory Status:

Listed

Canada DSL:

Listed

Phenol, polymer with formaldehyde, glycidyl ether :

TSCA Inventory Status:

Listed

Canada DSL:

Listed

Canadian Regulations.

WHMIS Hazard Class(es): D2B

SECTION 16 - ADDITIONAL INFORMATION

HMIS Fire Hazard: HMIS Health Hazard: HMIS Reactivity: HMIS Personal Protection: MSDS Revision Date: MSDS Author: Disclaimer:

1
2*
1
x
12/15/2009
Actio Corporation
This Health and Safety Information is correct to the best of our knowledge and belief at the date of its publication but we cannot accept liability for any loss, injury or damage which may result from its use. The information given in the Data Sheet is designed only as a guidance for safe handling, storage and the use of the substance. It is not a specification nor does it guarantee any specific properties. All chemicals should be handled only by competent personnel, within a controlled environment.

Copyright© 1996-2010 Actio Software Corporation. All Rights Reserved.

MSDS Name
Manufacturer Name Stock No.: Kit MSDS Revision Date
Components :

DEVCON® HP250 (2:1 ratio) straw - use DA091 2:1 plunger ITW Devcon 14315 12/15/2009
HP 250 HI-PERFORMANCE ADHESIVE HARDENER HP250 HI-PERFORMANCE ADHESIVE RESIN
ITW Devcon Product Code : 14315

Save page as PDF

View MSDS : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION

Product Name: Manufacturer Name: Address:
General Phone Number: Emergency Phone Number: CHEMTREC: Canutec: MSDS Revision Date:

HP 250 HI-PERFORMANCE ADHESIVE HARDENER ITW Devcon 30 Endicott Street Danvers, MA 01923 (978) 777-1100 (800) 424-9300 For emergencies in the US, call CHEMTREC: 800-424-9300 In Canada, call CANUTEC: (613) 996-6666 (call collect) 12/15/2009

HMIS Health Hazard 3*
Fire Hazard 1
REACTIVITY 0 Personal x Prote ction
* Chronic Health
Effe cts :

SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Name

CAS#

Ingredient Percent

Inert material Nonylphenol Non-hazardous ingredients. 4, 4'-Methylenebiscyclohexanamine Triethylene glycol diamine Aminoethylpiperazine PACM Oligomers

N/A 25154-52-3 N/A 1761-71-3 929-59-9 140-31-8 135108-88-2

5 - 10 by weight 10 - 30 by weight 30 - 60 by weight 10 - 30 by weight 10 - 30 by weight 1 - 5 by weight 1 - 5 by weight

SECTION 3 - HAZARDS IDENTIFICATION

Emergency Overview: Route of Exposure:

DANGER! Corrosive. Potential Sensitizer. Irritant. Eyes. Skin. Inhalation. Ingestion.

Potential Health Effects: Eye: Skin:
Inhalation:
Ingestion: Chronic Health Effects:
Signs/Symptoms:
Target Organs: Aggravation of Pre-Existing Conditions:

Corrosive. Will cause eye burns, permanent tissue damage, and blindness.
Corrosive causes severe skin burns. may cause permanent skin damage. Allergic reactions are possible. May cause skin sensitization, an allergic reaction, which becomes evident on reexposure to this material.
May cause severe respiratory system irritation. May cause respiratory sensitization with asthma-like symptoms in susceptible individuals.
Harmful if swallowed. Corrosive to the gastrointestinal tract.
Prolonged skin contact causes burns. Repeated or prolonged inhalation may cause toxic effects.
Depending on solution concentration, material may be corrosive to skin, mucous membranes and eyes. Vapors may cause respiratory irritation.
Eyes. Skin. Respiratory system. Digestive system.
Individuals with pre-existing skin disorders, asthma, allergies or known sensitization may be more susceptible to the effects of this product.

SECTION 4 - FIRST AID MEASURES

Eye Contact: Skin Contact:
Inhalation: Ingestion: Other First Aid:

Immediately flush eyes with plenty of water for at least 15 to 20 minutes. Ensure adequate flushing of the eyes by separating the eyelids with fingers. Get immediate medical attention.
Immediately wash skin with plenty of soap and water for 15 to 20 minutes, while removing contaminated clothing and shoes. Get medical attention if irritation develops or persists.
If inhaled, remove to fresh air. If not breathing, give artificial respiration or give oxygen by trained personnel. Seek immediate medical attention.
If swallowed, do NOT induce vomiting. Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person.
Due to possible aspiration into the lungs, DO NOT induce vomiting if ingested. Provide a glass of water to dilute the material in the stomach. If vomiting occurs naturally, have the person lean forward to reduce the risk of aspiration.

SECTION 5 - FIRE FIGHTING MEASURES

Flammable Properties: Flash Point: Flash Point Method: Auto Ignition Temperature: Lower Flammable/Explosive Limit: Upper Flammable/Explosive Limit: Fire Fighting Instructions:
Extinguishing Media:
Unsuitable Media: Protective Equipment:

Class III B. >200°F (93.3°C)
Pensky-Martens Closed Cup
Not determined. Not determined.
Not determined.
Evacuate area of unprotected personnel. Use cold water spray to cool fire exposed containers to minimize risk of rupture. Do not enter confined fire space without full protective gear. If possible, contain fire run-off water. Use carbon dioxide (CO2) or dry chemical when fighting fires involving this material. Water or foam may cause frothing.
As in any fire, wear Self-Contained Breathing Apparatus (SCBA), MSHA/NIOSH (approved or equivalent) and full protective gear.

SECTION 6 - ACCIDENTAL RELEASE MEASURES

Spill Cleanup Measures:
Personnel Precautions: Environmental Precautions: Other Precautions:

Absorb spill with inert material (e,g., dry sand or earth), then place in a chemical waste container. Provide ventilation. Clean up spills immediately observing precautions in the protective equipment section. After removal, flush spill area with soap and water to remove trace residue. Corrosive. Avoid personal contact and breathing vapors or mists. Ventilate area. Use proper personal protective equipment as listed in section 8.
Evacuate area and keep unnecessary and unprotected personnel from entering the spill area.
Avoid runoff into storm sewers, ditches, and waterways.
Pump or shovel to storage/salvage vessels.

SECTION 7 - HANDLING and STORAGE

Handling: Storage: Special Handling Procedures: Hygiene Practices:

Use with adequate ventilation. Avoid breathing vapor, aerosol or mist. Avoid contact with eyes and skin. Do not reuse containers without proper cleaning or reconditioning.
Store in a cool, dry, well ventilated area away from sources of heat and incompatible materials. Keep container tightly closed when not in use. Do not store in reactive metal containers. Keep away from acids, oxidizers.
Provide appropriate ventilation/respiratory protection against decomposition products (see Section 10) during welding/flame cutting operations and to protect against dust during sanding/grinding of cured product.
Wash thoroughly after handling.

SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION - EXPOSURE GUIDELINES

Engineering Controls:
Eye/Face Protection: Skin Protection Description: Respiratory Protection:
Other Protective:

Use appropriate engineering control such as process enclosures, local exhaust ventilation, or other engineering controls to control airborne levels below recommended exposure limits. Good general ventilation should be sufficient to control airborne levels. Where such systems are not effective wear suitable personal protective equipment, which performs satisfactorily and meets OSHA or other recognized standards. Consult with local procedures for selection, training, inspection and maintenance of the personal protective equipment.
Wear appropriate protective glasses or splash goggles as described by 29 CFR 1910.133, OSHA eye and face protection regulation, or the European standard EN 166.
Chemical-resistant gloves and chemical goggles, face-shield and synthetic apron or coveralls should be used to prevent contact with eyes, skin or clothing.
A NIOSH approved air-purifying respirator with an organic vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed exposure limits. Protection provided by air purifying respirators is limited. Use a positive pressure air supplied respirator if there is any potential for an uncontrolled release, exposure levels are not known, or any other circumstances where air purifying respirators may not provide adequate protection.
Facilities storing or utilizing this material should be equipped with an eyewash and a deluge shower safety station.

EXPOSURE GUIDELINES Notes :

Only established PEL and TLV values for the ingredients are listed.

SECTION 9 - PHYSICAL and CHEMICAL PROPERTIES

Physical State Appearance: Color: Odor: Boiling Point: Melting Point: Specific Gravity: Solubility: Vapor Density: Vapor Pressure: Percent Volatile: Evaporation Rate: pH: Molecular Formula: Molecular Weight: Flash Point: Flash Point Method: Auto Ignition Temperature: VOC Content:

Viscous. Liquid.. Amber.. Ammonia like fishy. Not determined. Not determined. 0.99 >15% Not determined. Not determined. 0 Not determined. alkaline Mixture Mixture >200°F (93.3°C) Pensky-Martens Closed Cup Not determined. 0 g/L

Percent Solids by Weight

100

SECTION 10 - STABILITY and REACTIVITY

Chemical Stability: Hazardous Polymerization: Conditions to Avoid:
Incompatible Materials:

Stable under normal temperatures and pressures.
Not reported.
Extreme heat, sparks, and open flame. Incompatible materials, oxidizers and oxidizing conditions. Product may slowly corrode copper, aluminum, zinc and galvanized surfaces.
Oxidizers, acids, and chlorinated organic compounds. Reactive metals (e.g. sodium, calcium, zinc). Sodium/calcium hypochlorite. Nitrous acid/ oxide, nitrites. Peroxides. Materials reactive with hydroxyl compounds.

SECTION 11 - TOXICOLOGICAL INFORMATION

Nonylphenol :

RTECS Number:

SM5600000

Skin:

Oral - Rat LD50: 580 mg/kg [Details of toxic effects not reported other than lethal dose value.] Oral - Mouse LD50: 1231 mg/kg [Details of toxic effects not reported other than lethal dose value.] Administration onto the skin - Rabbit LD50: 2140 uL/kg [Details of toxic effects not reported other than lethal dose value.] Administration onto the skin - Rabbit LD50: 2140 mg/kg [Details of toxic effects not reported other than lethal dose value.] Oral - Mouse LD50: 75.63 mL/kg [Details of toxic effects not reported other than lethal dose value.] Administration onto the skin - Rabbit Open irritation test: 500 mg

Ingestion:

Oral - Rat LD50: 580 mg/kg [Details of toxic effects not reported other than lethal dose value.] Oral - Mouse LD50: 1231 mg/kg [Details of toxic effects not reported other than lethal dose value.] Oral - Mouse LD50: 75.63 mL/kg [Details of toxic effects not reported other than lethal dose value.]

4, 4'-Methylenebiscyclohexanamine :

RTECS Number:

GX1530000

Eye:

Eye - Rabbit Standard Draize Test. : 10 uL/24H [severe ]

Inhalation:

Inhalation - Mouse LC50 : 400 mg/m3/4H [Details of toxic effects not reported other than lethal dose value. ]

Aminoethylpiperazine :

RTECS Number:

TK8050000

Eye:

Eye - Rabbit Standard Draize Test.: 20 mg/24H [Moderate]

Skin:

Oral - Rat LD50 : 2140 uL/kg [Details of toxic effects not reported other than lethal dose value.] Intraperitoneal. - Mouse LD50 : 250 mg/kg [Details of toxic effects not reported other than lethal dose value.] Administration onto the skin - Rabbit LD50 : 880 uL/kg [Details of toxic effects not reported other than lethal dose value.]

Ingestion:

Administration onto the skin - Rabbit Open irritation test: 100 ug/24H
Oral - Rat LD50 : 2140 uL/kg [Details of toxic effects not reported other than lethal dose value.]

SECTION 12 - ECOLOGICAL INFORMATION

Ecotoxicity: Environmental Fate:

No ecotoxicity data was found for the product. No environmental information found for this product.

SECTION 13 - DISPOSAL CONSIDERATIONS

Waste Disposal:

Consult with the US EPA Guidelines listed in 40 CFR Part 261.3 for the
EffectsSkinDetailsProductEyes