Serial ATA Hard Drive Dock

Preparing to load PDF file. please wait...

0 of 0
100%
Serial ATA Hard Drive Dock

Transcript Of Serial ATA Hard Drive Dock

T-203K Instruction Manual
Serial ATA Hard Drive Dock
USB & eSATA to SATA External Dual Hard Drive Dock with Stand Alone Duplicator
page 1

Table of Contents
Features............................................................................ 2 Specifications................................................................... 3 Introduction ......................................................................  3
Packaging Contents......................................................... 3 System Requirements...................................................... 4 Installation......................................................................... 5 Hardware Installation.......................................................  6 Driver Installation............................................................. 7
Features:
• Stand Alone Duplicator • Install And Access Hard Drive in Seconds • Simple to Use Design; No Need to Add Enclosure or
Open Case • Compliance with Serial ATA International Organization:
Serial ATA Revision 2.6 • Support SATA 1.5G/3.0G Speed Negotiation • Support SATA II Asynchronous Signal Recovery (Hot
Plug) feature • Compliance with USB 2.0 electrical specification • Support  USB 2.0 High-Speed and Full-Speed Operation • Plug and Play
page 2

Specifications: BUS Interface:
External Connectors:
Chipset: Hard Drive bays: Hard Drive Compatibility:
Compatible Operating Systems:
Dimensions: Color: Power Adapter:

USB 2.0 & eSATA 1XUSBtype B 1X eSATA 1X DIN power connector
JMICRON JMB352 2 2.5” and 3.5” SATA 1.5 and 3Gb/s Windows 2000/XP/Server 2003/Vista , Mac OS X, Linux 168*109*81mm
Black
12V/2A & 5V/2A

Introduction:
The T-203 Dual Drive SATA Hard Drive Duplicator functions as both an external SATA hard drive docking station for 2.5” or 3.5” SATA/SATA II hard disks and a convenient standalone hard drive imaging solution, delivering an exact 1 to 1 disk copy

Packaging Contents:
• 1 x T-203 hard drive dock • 1 x Power Adapter with power cords • 1 x USB type A-B cable • 1 x eSATA Cable • 1 x Instruction Manual
page 3

System Requirements
• PC Systems Intel Pentium-III 500MHz equivalent or faster Windows 2000/XP/2003 Server/ Vista, Linux kernel 10.4.x or later. CD-ROM drive 64 MB of RAM (minimum) 250 MB of free disk space Super VGA (800 x 600) or higher resolution display with at least 256 colors Mouse or compatible pointing device SATA connection: SATA Host controller with Port Multiplier *support USB connection: USB 1.0 or 2.0 direct host connection or USB hub
• Macintosh Systems PowerMac G5, MacBook Pro or Mac Pro MacOS X, 9.2 (or later) CD-ROM drive Mouse or compatible pointing device SATA connection: SATA host controller with Port Multiplier *support USB connection: USB 1.0 or 2.0 direct host connection or
USB hub
*Port multiplier: A Serial ATA port multiplier is a device that allows one to connect multiple SATA devices to a single SATA
page 4

host port in a similar manner to that of a USB hub. If a host is not PM-aware, only a single drive is presented
Installation:
TOP VIEW
Drive Bay (Source)
Drive Bay (Destination)
REAR VIEW

Power Swith

DC USB Input type B eSATA
page 5

Duplicate start button

Hardware Installation:
JBOD Mode Connect the external power adapter to the Hard Drive Dock Install 1 or 2 hard drives into the dock in either drive bay Connect the USB cable or eSATA cable from the hard drive dock to the computer system and then press the power button The operating system should now detect the hard drive(s) and make them available The hard drives may need to be partitioned/formatted using a disk management utility before you can access them
Duplicator Mode Connect the external power adapter to the Hard Drive Dock Install 2 hard drives into the dock. Make sure to place the drive with the data you want copied (Source) into the “Source” bay. The destination disk (Destination) should be equal or larger in capacity than the source disk. Press the power button. The Mode LED should be red. Once both drives are installed, press the Start button. The Mode LED will flashing, wait for 5 Seconds, the mode LED will OFF, and then Press the Start button again to confirm the duplication progress. You will see the HDD active LED flashing until the whole destination progress. When the duplication of hard drive successfully complete, all the LED are OFF
page 6

HDD Active LED (source bay)

Mode LED

HDD Active LED (source bay)

Driver Installation:
Windows 2000/XP/Vista, Mac OS X, Linux kernel No driver installation is required for these operating
systems, as this hard drive dock is natively supported, so
the drivers are already installed

page 7
Drive DockModeDrivesDriveAta